FORMULIERUNGEN

Phase A: Combine all ingredients of phase A and stir until everything is completely dissolved. Heat to 75 °C.
Phase B: Combine all ingredients and heat to 75 °C. Add then phase B to phase A under strong stirring and homogenise.
Phase C: Add phase C to the formulation and stir.
Adjust the pH to 5.5 ± 0.05.

Appearance: White, fluid emulsion
pH: 5.5 ± 0.05
Stability: No separation after centrifugation (4000 rpm, 30 min), stable for 3 months at room temperature and 40 °C
Microbiological stability: proven

Phase A: Combine all ingredients of phase A under stirring until Cosphaderm® X 34 is completely dissolved.
Phase B: Combine all ingredients of phase B.
Heat both phases separately to 70 °C and add phase B to phase A under stirring.
After stirring homogenise the formulation and adjust the pH to 5.5 ± 0.05.

Appearance: White, shiny, low viscous emulsion
pH: 5.5 ± 0.05
Stability: No separation after centrifugation (4000 rpm, 30 min), stable for 3 months at room temperature and 40 °C
Microbiological stability: proven

Phase A: Combine all ingredients of phase A and stir until everything is completely dissolved.
Phase B: Combine all ingredients of phase B.
Heat both phases separately to 75-80 °C. Add phase B to A while stirring and then homogenise.
Adjust the pH to 5.5 ± 0.05.

Appearance: White, viscous gel cream
pH: 5.5 ± 0.05
Stability: No separation after centrifugation (4000 rpm, 30 min), stable for 3 months at room temperature and 40 °C
Microbiological stability: proven

Phase A: Combine all ingredients of phase A and stir until everything is completely dissolved.
Heat the water phase to 70-75 °C.
Phase B: Combine all ingredients of phase B and heat to 75°C. Phase C is added to the oil phase just before emulsion is formed.
Add phase B+C to the water phase while stirring. Homogenise at 40°C.
Adjust the pH to 5.5 ± 0.05.

Appearance: White, high viscous cream
pH: 5.5 ± 0.05
Stability: No separation after centrifugation (4000 rpm, 30 min), stable for 3 months at room temperature and 40 °C
Microbiological stability: proven

Phase A: Mix all ingredients together.
Phase B: Slowly add Cosphaderm® X 34 and Aristoflex® AVC under stirring to phase A. Continue stirring until complete dissolution. Then heat to 80 °C.
Phase C: Mix all ingredients and heat to 80 °C. Add phase C to phase A+B and homogenise.
Phase D: Add Cosphaderm® Dicapo below 40 °C under stirring.
Adjust the pH to 5.5 ± 0.05.

Appearance: Light beige, shiny, viscous emulsion
pH: 5.5 ± 0.05
Stability: No separation after centrifugation (4000 rpm, 30 min), stable for 3 months at room temperature and 40 °C
Microbiological stability: proven

Phase A: Combine all ingredients of phase A.
Phase B: Disperse Cosphaderm® KG in glycerol and add it to phase A. Stir until completely dissolved.
Phase C: Add phase C and stir until everything is homogeneous.
Phase D: Prepare phase D and melt at 50 °C, then cool down to room temperature.
Add phase D to the water phase and homogenise.
Adjust pH to 5.5 ± 0.05.

Appearance: Shiny, viscous emulsion
pH: 5.5 ± 0.05
Stability: No separation after centrifugation (4000 rpm, 30 min), stable for 3 months at room temperature and 40 °C
Microbiological stability: proven

Phase A: Combine all ingredients of phase A and raise the pH to 11 to dissolve the cinnamic acid completely. Afterwards, adjust the pH to 5.5 ± 0.05 by adding Citric Acid.
Phase B: Add phase B to phase A while stirring. Stir until everything is completely dissolved.
Phase C: Prepare phase C and heat both phases separately to 75 °C.
Add phase C to phase A/B under stirring and homogenise the mixture.
Phase D: Add phase D to the formulation.
Adjust the pH to 5.5 ± 0.05.

Appearance: Black, creamy paste with small exfoliants
pH: 5.5 ± 0.05
Stability: No separation after centrifugation (4000 rpm, 30 min), stable for 3 months at room temperature and 40 °C
Microbiological stability: proven

Phase A: Combine all ingredients of phase A and stir until everything is completely dissolved. Heat to 70-75 °C.
Phase B: Combine all ingredients of phase B and heat to 75°C. Phase C is added to the oil phase just before emulsion is formed.
Add phase B+C to the water phase while stirring. Homogenise at 40°C.
Adjust the pH to 5.5 ± 0.05.

Appearance: White, viscous cream
pH: 5.5 ± 0.05
Stability: No separation after centrifugation (4000 rpm, 30 min), stable for 3 months at room temperature and 40 °C
Microbiological stability: proven

Combine all ingredients of phase A and heat to 80-85 °C.
When everything has melted, take off heat and fill into packaging.

Appearance: Solid, yellowish balm
Stability: Stable for 3 months at room temperature and 40 °C
Microbiological stability: proven (Water activity value less than 0.75)

Prepare phase A and heat to 70 °C until fully melted.
Fill into lip balm container and let it cool.

Appearance: Yellow solid balm
Stability: Stable for 3 months at room temperature and 40 °C
Microbiological stability: proven (Water activity value less than 0.75)

Phase A: Combine all ingredients of phase A and stir until everything is dissolved.
Phase B: Slowly add phase B to phase A under stirring. Stir until complete dissolution.
Adjust pH to 5.5 ± 0.05 and heat phase A and B to 70 °C.
Phase C: Combine all ingredients and heat phase C to 70 °C. Add then phase C to phase A and B under strong stirring and homogenise the formulation.
Adjust pH to 5.2 ± 0.05.

Appearance: Slightly yellowish gel cream
pH: 5.2 ± 0.05
Stability: No separation after centrifugation (4000 rpm, 30 min), stable for 3 months at room temperature and 40 °C
Microbiological stability: proven

Phase A: Mix all ingredients together and stir until homogeneous.
Phase B: Combine all ingredients and add phase B to A while stirring.

Appearance: White powder
Stability: stable for 3 months at room temperature and 40 °C
Microbiological stability: proven (Water activity value less than 0.75)

Phase A: Combine all ingredients of phase A and stir until everything is completely dissolved.
Phase B: Add Cosphaderm® SF-75H to phase A and let it soak for 10-20 minutes. Then heat phase A+B to 70 °C.
Phase C: Combine all ingredients of phase C and heat to 70 °C. Add then phase C to phase A+B under
strong stirring and homogenise the formulation.
Adjust the pH to 5.0 ± 0.05.

Appearance: Light beige gel cream
pH: 5.0 ± 0.05
Stability: No separation after centrifugation (4000 rpm, 30 min), stable for 3 months at room temperature and 40 °C
Microbiological stability: proven

Phase A: Combine all ingredients of phase A and stir until everything is completely dissolved.
Phase B: Combine all ingredients of phase B.
Heat both phases separately to 70-75 °C and add phase B to A while homogenising.
Phase C: Dissolve Cosphaderm® Magnolia Extract 98 in Cosphaderm® Diols. Add phase C to phase A/B under stirring.
Adjust the pH to 4.0 ± 0.05.

Appearance: Beige, viscous gel cream
pH: 4.0 ± 0.05
Stability: No separation after centrifugation (4000 rpm, 30 min), stable for 3 months at room temperature and 40 °C
Microbiological stability: proven

Phase A: Combine all ingredients of phase A and stir until everything is completely dissolved.
Phase B: Combine all ingredients of phase B.
Heat both phases separately to 70-75 °C and add phase B to A very slowly while homogenising.
Phase C: Cool down to 40°C and add Phase C.

Appearance: Slightly yellowish high viscous gel
Stability: stable for 3 months at room temperature and 40 °C
Microbiological stability: proven (Water activity value less than 0.75)

Phase A: Combine water and Cosphagard® SA natural and raise the pH value to 10 – 11. Stir until complete dissolution. Afterwards lower the pH to approximately 6.
Phase B: Add phase B to phase A and stir until everything is completely dissolved. Heat to 70 °C.
Phase C: Combine all ingredients of phase C and heat to 70 °C.
Add phase C to A+B while stirring. Homogenise at 40°C.
Phase D: Add Cosphaderm® TOM to the emulsion.
Adjust pH to 6.0 ± 0.05.

Appearance: Light beige lotion
pH: 6.0 ± 0.05
Stability: No separation after centrifugation (4000 rpm, 30 min), stable for 3 months at room temperature and 40 °C
Microbiological stability: proven

Phase A: Combine all ingredients and stir until everything is completely dissolved.
Phase B: Combine phase B separately and add phase B to phase A under soft stirring. Stir until both phases are mixed.
Phace C: Add phenylpropanol to phase A+B. Adjust th pH to 5.5 ± 0.05.

Appearance: Transparent, viscous liquid
pH: 5.5 ± 0.05
Stability: No separation after centrifugation (4000 rpm, 30 min), stable for 3 months at room temperature and 40 °C
Microbiological stability: proven

Phase A: Combine all the ingredients of phase A and melt, then leave to cool.
Phase B: Add phase B and pour into packaging.
The mixture thickens after a while.

Appearance: Yellowish paste with salt
Stability: stable for 3 months at room temperature and 40 °C
Microbiological stability: proven (Water activity value less than 0.75)

Phase A: Combine all ingredients of phase A and stir until everything is completely dissolved.
Phase B: Combine all ingredients of phase B.
Heat both phases separately to 75 °C and add phase B to A while stirring. Stir cold and homogenise at 40°C.
Adjust the pH to 5.5 ± 0.05.

Appearance: White high viscous emulsion
pH: 5.5 ± 0.05
Stability: No separation after centrifugation (4000 rpm, 30 min), stable for 3 months at room temperature and 40 °C
Microbiological stability: proven

Phase A: Combine all ingredients of phase A and stir until everything is completely dissolved. Adjust the pH to 5.5 ± 0.05.
Phase B: Combine all ingredients and melt at 40-50 °C. Then add phase A to phase B while homogenising.

Appearance: White viscous lotion
pH: 5.5 ± 0.05
Stability: No separation after centrifugation (4000 rpm, 30 min), stable for 3 months at room temperature and 40 °C
Microbiological stability: proven

Combine all ingredients of phase A, heating to 75 °C. When everything has melted, add phase B. Take off heat and fill into packaging.

Appearance: Solid, yellowish balm
Stability: stable for 3 months at room temperature and 40 °C
Microbiological stability: proven (Water activity value less than 0.75)

Phase A: Prepare phase A and heat to 70 °C until fully melted.
Stir until completely dissolved.
Pour into container and let it cool down.

Appearance: Yellow balm
Stability: stable for 3 months at room temperature and 40 °C
Microbiological stability: proven (Water activity value less than 0.75)

Phase A: Mix all ingredients together and stir until homogeneous.

Appearance: Yellow liquid
Stability: stable for 3 months at room temperature and 40 °C
Microbiological stability: proven (Water activity value less than 0.75)

Phase A: Prepare phase A. Raise the pH to 10 to dissolve Cosphaderm® pAS natural and stir until everything is completely dissolved. Afterwards, adjust the pH to 5.5 ± 0.05 by adding Citric Acid.
Phase B: Add all ingredients of phase B to phase A. Then heat phase A+B to 75 °C.
Phase C: Combine all ingredients and heat to 75 °C. Add then phase C to phase A+B under strong stirring and homogenise.
Phase D: Dissolve menthol in ethanol and add phase D below 40°C.
Adjust the pH to 5.5 ± 0.05.

Appearance: White viscous emulsion
pH: 5.5 ± 0.05
Stability: No separation after centrifugation (4000 rpm, 30 min), stable for 3 months at room temperature and 40 °C
Microbiological stability: proven

Phase A: Combine all ingredients of phase A and stir until everything is completely dissolved. Heat phase A to 80°C.
Phase B: Prepare phase B and heat to 80°C. Add phase B to A under stirring.
Phase C: Add phase C below 40°C to the formulation. Homogenise.
Adjust the pH value to 5.5 ± 0.05.

Appearance: White to slightly yellowish lotion
pH: 5.5 ± 0.05
Stability: Microbiological stability proven, no separation after centrifugation (4000 rpm, 30 min)

Phase A: Combine all ingredients of phase A and stir until everything is completely dissolved.
Adjust the pH to 5.5 ± 0.05.
Phase B: Combine all ingredients of phase B.
Heat phase B to 80 °C and slowly add phase A to B while homogenising.

Appearance: White low viscous lotion
pH: 5.5 ± 0.05
Stability: No separation after centrifugation (4000 rpm, 30 min), stable for 3 months at room temperature and 40 °C
Microbiological stability: proven

Phase A: Combine all ingredients of phase A. Stir until everything is completely dissolved. Afterwards, adjust the pH to 5.5 ± 0.05.
Phase B: Combine all ingredients and heat to 75-80 °C. Then add phase B to phase A while homogenising.
Add phase C to the finished formulation and homogenise.

Appearance: White low viscous emulsion
Stability: No separation after centrifugation (4000 rpm, 30 min), stable for 3 months at room temperature and 40 °C
Microbiological stability: proven

Phase A: Combine all ingredients of phase A and stir until complete dissolution.
Adjust the pH value to 5.5 ± 0.05.
Phase B: Prepare phase B in a separate beaker.
Add phase B to phase A without stirring.

Appearance: Two-phase system with yellowish oil phase on top of a clear water phase
pH: 5.5 ± 0.05
Stability: stable for 3 months at room temperature and 40 °C
Microbiological stability: proven

Phase A: Mix all ingredients together and heat to 80-85 °C until everything is melted.
Phase B: Add all ingredients of phase B to phase A at 70°C.
Phase C: Premix the pigments in the oils until everything is homogeneous and add it to the hot phase A+B and fill into packaging.

Appearance: Solid stick
Stability: stable for 3 months at room temperature and 40 °C
Microbiological stability: proven (Water activity value less than 0.75)

Phase A: Prepare phase A and heat to 60-65 °C. Stir until complete dissolution.
Phase B: Let the mixture cool down and add phase B at room temperature.
Phase C: Add colour as desired.

Appearance: Yellowish oil gel with sugar beads
Stability: stable for 3 months at room temperature and 40 °C
Microbiological stability: proven (Water activity value less than 0.75)