FORMULIERUNGEN

MANUFACTURING PROCESS
Phase A: Combine all ingredients of phase A and stir until everything is completely dissolved.
Phase B: Combine all ingredients of phase B.
Heat both phases separately to 70-75 °C and add phase B to A while homogenising.
Phase C: Dissolve Cosphaderm® Magnolia Extract 98 in Cosphaderm® Capo. Add phase C to phase A/B under stirring.
Adjust the pH to 4.0 ± 0.05.

SPECIFICATION
Appearance: beige emulsion
pH: 4.0 ± 0.05
Stability: Microbiological stability proven, no separation after centrifugation (4000 rpm, 30 min)

Manufacturing Process
Phase A: Combine all ingredients of phase A and stir until everything is homogeneous.
Phase B: Simply add lukewarm tap water to the bottle, then add in your powder shampoo. Shake for approximately 30 seconds and wait until everything has been dissolved. Let the mixture rest for 24 h.

Specification
Appearance: Pearlescent gel
pH: 5.5 ± 0.10
Stability: Microbiological stability proven, no separation after centrifugation (4000 rpm, 30 min)

Manufacturing Process
Combine all ingredients of phase A, heating to 80°C. When everything has melted, add phase B. Take off heat and pour into molds.

Specification
Appearance: Solid, yellowish bar
Stability: Microbiological stability proven (Water activity value less than 0.75)

Manufacturing Process
Phase A: Combine all ingredients of phase A and stir until everything is dissolved.
Phase B: Combine all ingredients and heat phase B to 40 – 50 °C.
Afterwards combine phase A and B while stirring slowly until a homogeneous gel is formed.
Phase C: Add panthenol to the mixture (<40 °C).
Adjust pH to 5.5 ± 0.05.

Specification
Appearance: Yellowish, slightly turbid, viscous gel
pH: 5.5 ± 0.05
Stability: Microbiological stability proven, no separation after centrifugation (4000 rpm, 30 min)

Manufacturing Process
Phase A: Combine all ingredients of phase A. Raise the pH to 11 to dissolve Cosphagard® SA natural.
Heat phase A to 70 °C.
Phase B: Combine all ingredients and stir until Cosphaderm® X 34 is completely dissolved.
Heat phase B to 70 °C.
Add phase B to phase A under very soft stirring.
Phase C: Add phase C below 40 °C to the finished formulation. Adjust the pH to 4.5 ± 0.05.
The shampoo will thicken within 24 hours.

Specification
Appearance: Clear to yellowish liquid
pH: 4.5 ± 0.05
Stability: Microbiological stability proven, no separation after centrifugation (4000 rpm, 30 min)

Manufacturing Process
Phase A: Combine all ingredients of phase A. Raise the pH to 11 to dissolve Cosphagard® SA natural and Cosphaderm® pAS natural.
Heat phase A to 70 °C.
Phase B: Combine all ingredients and stir until Cosphaderm® X 34 is completely dissolved.
Heat phase B to 70 °C.
Add phase B to phase A under very soft stirring.
Phase C: Add phase C below 40 °C to the finished formulation. Adjust the pH to 4.5 ± 0.05.
The shampoo will thicken within 24 hours.

Specification
Appearance: Clear to yellowish liquid
pH: 4.5 ± 0.05
Stability: Microbiological stability proven, no separation after centrifugation (4000 rpm, 30 min)

Manufacturing Process
Phase A: Combine all ingredients of phase A and stir slowly until Cosphaderm® CA natural is completely
dissolved.
Phase B: Combine all ingredients of phase B and stir until Cosphaderm® X soft is dissolved.
Heat both phases separately to 50 °C and add phase B to phase A under thorough stirring with
the propeller stirrer. Adjust the pH to 5.5 ± 0.05.

Specification
Appearance: Milky, white gel
pH: 5.5 ± 0.05
Stability: Microbiological stability proven, no separation after centrifugation (4000 rpm, 30 min)

Manufacturing Process
Phase A: Combine all ingredients and dissolve Phase A at 40°C.
Phase B: Add phase B to phase A and adjust the pH to 5.0 – 5.5.
Phase C: Add phase C to phase A/B under soft stirring.
Phase D: Dissolve Cosphaderm® Magnolia Extract 98 in Cosphaderm® Propanediol natural and Cosphaderm® TOM. Add phase D to phase A/B/C under stirring.
Adjust the pH to 5.0 ± 0.05.

Specification
Appearance: Yellowish gel
pH: 5.0 ± 0.05
Stability: Microbiological stability proven, no separation after centrifugation (4000 rpm, 30 min)

MANUFACTURING PROCESS
Phase A: Combine all ingredients of phase A and stir until everything is completely dissolved.
Phase B: Combine all ingredients of phase B.
Heat both phases separately to 75-80 °C.  Add phase B to A while stirring and then homogenise.
Adjust the pH to 5.5 ± 0.05.

SPECIFICATION
Appearance: White gel cream
pH: 5.5 ± 0.05
Stability: Microbiological stability proven, no separation after centrifugation (4000 rpm, 30 min)

Manufacturing Process
Phase A: Combine all ingredients of phase A. Raise the pH to 11 to dissolve Cosphagard® SA natural. When everything is dissolved, lower the pH back to 4-5 again.
Phase B: Combine Glycerin, Cosphaderm® X 34 and Cosphaderm® Sodium Hyaluronate high and stir until the powder is wetted. Then add it to phase A.
Phase C: Add phase C under stirring.
Adjust the pH to 4.0 ± 0.05.

Specification
Appearance: Transparent, clear gel
pH: 4.0 ± 0.05
Stability: Microbiological stability proven, no separation after centrifugation (4000 rpm, 30 min)

MANUFACTURING PROCESS
Phase A: Combine all ingredients of phase A and raise the pH to 10 to dissolve Cosphaderm® pAS natural. Stir until everything is completely dissolved. Afterwards, adjust the pH to 5.5 ± 0.05 by adding Citric Acid.
Phase B: Add all ingredients of phase B to phase A.
Phase C: Combine all ingredients and heat to 80 °C. Then add phase A/B to phase C while homogenising.
Add phase D to the finished formulation and homogenise.

SPECIFICATION
Appearance: White, slightly beige cream
pH: 5.5 ± 0.05
Stability: Microbiological stability proven, no separation after centrifugation (4000 rpm, 30 min)

MANUFACTURING PROCESS
Combine all ingredients of phase A, heating to 80-85 °C. When everything has melted, take off heat and fill into packaging.

SPECIFICATION
Appearance: Solid, yellowish balm
Stability: Microbiological stability proven (Water activity value less than 0.75)

Manufacturing Process
Phase A: Combine all ingredients of phase A. Raise the pH to 11 to dissolve Cosphagard® SA natural
completely.
Phase B: Add phase B and lower the pH to 4.0 ± 0.05.

Specification
Appearance: Clear solution
pH: 4.0 ± 0.05
Stability: Microbiological stability proven, no separation after centrifugation (4000 rpm, 30 min)

Manufacturing Process
Phase A: Mix all ingredients except water, then add water and stir until everything is completely
dissolved.
Phase B: Mix all ingredients and homogenise on high-speed for 5 minutes.
Add phase B to A slowly while gently stirring for 10 minutes.
Adjust the pH to 5.45 – 5.55.
Heat the mixture to 90 – 100 °C and keep this temperature for 2 – 3 minutes (Warning: Lecithins are heat
sensitive. Therefore, the process of heating should be kept to a minimum!).
Pour the hot mixture into a suitable mould as fast as possible and let it cool down.

Specification
Appearance: White to off-white gel
pH: 5.5 ± 0.05
Stability: Microbiological stability proven

Manufacturing Process
Phase A: Combine all ingredients of phase A under stirring. Stir until Cosphaderm® X 34 is completely
dissolved. Raise the pH to 11 to dissolve Cosphaderm® CA natural.
Phase B: Add Cosphaderm® SF-75H to phase A under stirring and let it soak for 10 minutes. Then heat
phase A+B to 80 °C.
Phase C: Combine all ingredients of phase C and heat to 80 °C. Add then phase C to phase A+B under
strong stirring and homogenise the formulation.
Phase D: Add Cosphaderm® GeMix below 40 °C.
Adjust the pH to 5.5 ± 0.05.

Specification
Appearance: White cream
pH: 5.5 ± 0.05
Stability: Microbiological stability proven, no separation after centrifugation (4000 rpm, 30 min)

Manufacturing Process
Phase A: Combine all ingredients of phase A under stirring until Cosphaderm® X 34 is completely dissolved.
Phase B: Combine all ingredients of phase B. Heat both phases separately to 70 °C and add phase B
to phase A under stirring.
After stirring for 5 minutes homogenise the formulation and adjust the pH to 5.5 ± 0.05.

Specification
Appearance: White, shiny emulsion
pH: 5.5 ± 0.05
Stability: Microbiological stability proven, no separation after centrifugation (4000 rpm, 30 min)

Manufacturing Process
Phase A: Combine all ingredients of phase A and stir until everything is completely dissolved.
Adjust pH to 5.5 ± 0.05 if necessary.

Specification
Appearance: Transparent serum
pH: 5.5 ± 0.05
Stability: Microbiological stability proven, no separation after centrifugation (4000 rpm, 30 min)

Manufacturing Process
Phase A: Combine all ingredients of phase A.
Phase B: Prepare Glycerin, Cosphaderm® Propanediol natural and Cosphaderm® X 34 first.
Disperse Cosphaderm® X 34 with a stirrer. Peel 50 g fruit/vegetable A and 50 g fruit/vegetable B and crush it separately in a mixer. Filter the crushed fruits in separate beakers. Slowly add the filtered fruits/vegetables and the water to the mixture of Glycerin, Cosphaderm® Propanediol natural and Cosphaderm® X 34 under stirring and stir until complete dissolution.
Add remaining ingredients. Heat phase A and B separately to 70 °C and add phase A to phase B under stirring.
Phase C: Add Cosphaderm® MultiMEG below 40 °C. Adjust the pH value to 5.5 ±
0.05.

Specification
Appearance: Light, shiny cream
pH: 5.5 ± 0.05
Stability: Microbiological stability proven, no separation after centrifugation (4000 rpm, 30 min)

Manufacturing Process
Phase A: Combine all ingredients of phase A except Cosphaderm® CA natural and
Cosphaderm® LA-T and stir for 10 min at 1500 rpm. Add Cosphaderm® CA natural and raise the pH to 11
to dissolve it completely.
Then add Cosphaderm® LA-T to lower the pH again.
Phase B: Prepare phase B and heat phase A and phase B separately to 75 °C.
Add phase B to phase A under thorough stirring with the propeller stirrer and homogenise the mixture.
Phase C: Add Cosphaderm® Magnolia Extract 98 to phase A+B under stirring and below 40 °C.
Phase D: Prepare phase D and add it to the formulation. Let the mask cool down under moderate
stirring.
Adjust the pH to 5.5 ± 0.05.

Specification
Appearance: Black, creamy paste with small exfoliants
pH: 5.5 ± 0.05
Stability: Microbiological stability proven, no separation after centrifugation (4000 rpm, 30 min)

Manufacturing Process
Phase A: Prepare phase A and melt at 50 °C, then cool down to room temperature.
Phase B: Prepare phase B and stir for 10 min.
Phase C: Prepare all ingredients of phase C except water. Slowly add the water and stir until completely dissolved.
Combine phase A and B and homogenise. Add phase A+B slowly to phase C under stirring.
Adjust pH to 5.5 ± 0.05.

Specification
Appearance: Shiny, viscous emulsion
pH: 5.5 ± 0.05
Stability: Microbiological stability proven, no separation after centrifugation (4000 rpm, 30 min)

Manufacturing Process
Phase A: Prepare phase A and stir until everything is completely dissolved. Adjust pH value to 5.5.
Phase B: Add Cosphaderm® Sodium pAS natural to phase A under stirring.
Phase C: Prepare phase C and homogenise for 5 minutes with high performance disperser (stator/rotor) at max. speed.
Add phase C to phase A+B in small steps under stirring.
Adjust pH value to 5.5 ± 0.05.

Specification
Appearance: Shiny emulsion
pH: 5.5 ± 0.05
Stability: Microbiological stability proven, no separation after centrifugation (4000 rpm, 30 min)