FORMULATIONS

MANUFACTURING PROCESS
Phase A: Combine all ingredients of phase A and stir until everything is completely dissolved.
Phase B: Add phase B to A while stirring.
Phase C: Add phase C to the water phase while stirring. Then heat the water phase to 70-75 °C.
Phase D: Combine all ingredients of phase D and heat to 75°C. Phase E is added to the oil phase just before emulsion is formed.
Add phase D+E to the water phase while stirring. Homogenise at 40°C.
Adjust the pH to 5.5 ± 0.05.

SPECIFICATION
Appearance: Light beige, high viscous cream
pH: 5.5 ± 0.05
Stability: No separation after centrifugation (4000 rpm, 30 min), stable for 3 months at room temperature and 40 °C
Microbiological stability: proven

Manufacturing Process
Phase A: Combine all ingredients of phase A.
Phase B: Melt all ingredients of phase B (35-40°C) and add to phase A. Mix until everything is homogeneous.
Press mixture into molds.

Specification
Appearance: Solid, white bar
Stability: stable for 3 months at room temperature and 40 °C
Microbiological stability: proven (Water activity value less than 0.75)

MANUFACTURING PROCESS
Phase A: Combine all ingredients of phase A and stir until everything is completely dissolved.
Phase B: Combine all ingredients of phase B.
Heat both phases separately to 75 °C and add phase B to A while stirring. Stir cold and homogenise at 40°C.
Adjust the pH to 5.5 ± 0.05.

SPECIFICATION
Appearance:  White emulsion
pH: 5.5 ± 0.05
Stability: Microbiological stability proven, no separation after centrifugation (4000 rpm, 30 min)

MANUFACTURING PROCESS
Combine all ingredients of phase A, heating to 75 °C. When everything has melted, add phase B. Take off heat and fill into packaging.

SPECIFICATION
Appearance: Solid, yellowish balm
Stability: Microbiological stability proven (Water activity value less than 0.75)

MANUFACTURING PROCESS
Phase A: Combine all ingredients of phase A and stir until everything is completely dissolved. Heat to 70-75 °C.
Phase B: Combine all ingredients and heat to 75 °C. Add then phase B to phase A under strong stirring and homogenise.
Phase C: Dissolve the menthol in Cosphaderm® Hexiol natural and add below 40°C.
Adjust the pH to 5.5 ± 0.05.

SPECIFICATION
Appearance: White emulsion
pH: 5.5 ± 0.05
Stability: Microbiological stability proven, no separation after centrifugation (4000 rpm, 30 min)

Manufacturing Process
Phase A: Combine all ingredients of phase A and raise the pH to 11 under stirring to dissolve cinnamic acid. When everything is dissolved, lower the pH back to 6 again.
Add phase B to A and stir until everything is dissolved. Heat phase A/B to 75 °C.
Phase C: Combine all ingredients and heat to 80 °C. Add then phase C to phase A/B under strong stirring and homogenise.
Adjust the pH to 5.5 ± 0.05.

Specification
Appearance: White emulsion
pH: 5.5 ± 0.05
Stability: Microbiological stability proven, no separation after centrifugation (4000 rpm, 30 min)

Manufacturing Process
Phase A: Combine all ingredients of phase A and stir until complete dissolution.
Adjust the pH value to 5.5 ± 0.05.
Phase B: Prepare phase B in a separate beaker.
Add phase B to phase A without stirring and pour mixture into spray flask.

Specification
Appearance: Two-phase system with oil phase on top of translucent water phase
pH: 5.5 ± 0.05
Stability: Microbiological stability proven

MANUFACTURING PROCESS
Phase A: Prepare phase A and heat to 60-65 °C. Stir until complete dissolution.
Phase B: Let the mixture cool down and add phase B at room temperature.
Phase C: Add colour as desired.

SPECIFICATION
Appearance: Yellowish oil gel
Stability: Microbiological stability proven (Water activity value less than 0.75)